Loading... Please wait...

Making Busty Aichan Bigger

Brand:


Product Review

 

This is a contribution from Mr. Lee who decided to make Busty Aichan Bigger. He sent me how to and pictures. Let's see how he did it. I'm attaching his emai here,
 
Let me first state two things before we begin. 1) I love the Ai Chan and if I had no choice, I would leave it alone. It is perfect. But as a man, I can't help but improve even on perfection. 2) I do not take any responsibility for damages to your Ai Chan. These instructions are to help improve the Ai Chan but you are following them at your own risk.

That being said, I wanted my Ai Chan bigger and had a pair of Quty Tits that I wasn't using. The pictures I've included shows the results of placing the Quty into the Ai Chan. The modified Busty Aichan in each image is on the left and the original Ai Chan on the right.
 
Image below shows only the left breast modified. All the rest of pictures are at the bottom of this page.
 
enlarge-busty-aichan-02.jpg
 
I must admit that after a few tries, this is a simple process. What I did was peal the skin and place the Quty in the underside and then glued the skin back in place. But my first try was a total disaster, so my best advice is to take your time and be patient. Work on one breast, let that settle for a day before moving onto the next. Once done, the chest case will no longer fit so you'll need to figure out another storage solution. Plus it becomes much heavier. But you will have a lot of fun.

Ok, let's get started. The Ai Chan is made up of 4 parts. A base structure that is its foundation. A outer skin layer and a inner skin layer that holds everything together. And a piece I call "flubber", which is shown in a photo below.

enlarge-busty-aichan-07.jpg

Flubber is a jelly like material that makes up the shape of the breast and makes the feel of the Ai Chan soft. So be careful with it and try not to deform it.

You will needthe following items:
A clean plastic card
Crazy glue
Baby powder
Scotch tap
Quty Tits
 
First clean and powder the Ai Chan. The powder will help prevent stickiness and limit any dirt from collecting. Before pealing the skin, I found that if I place it in a warm spot (like a garage on a hot day) for a few hours, it makes pealing the skin layer easier. Lay out a towel and place the Ai Chan on it, chest case upside down. With the breast cradled in its case, all the weight will be held in place, and that allows you to peal without having the whole structure wiggling around. The powder will make it difficult to tape the skin, but place a piece of tape on the side and at the bottom near the cleavage of one breast. You will be pealing between these two pieces of tape on the under side of the breast. Try to peal as small area as possible. The more you peal, the more you'll have to glue afterward.

Important note. You want to peal both skin layers. Do not separate the outer layer skin from the inner layer. Air bubbles will form, and it will be very difficult, almost impossible, to smooth it out.

Use your fingers to start pealing. Remember, you need to peal both skin layers to get to the flubber. Once the skin is lifted, hold the foundation and use a card to separate the flubber from that base. I found that if the Ai Chan is warm, the separation of flubber is easier. Scrape as deep as possible but try to keep the opening as narrow as possible. Tape down the open skin to keep it from shrinking back in place. Place the Quty Tits between the base and flubber. The skin layer and flubber is what gives the form of the breast. The Quty is only adding volume. So try placing it near the middle. With the Quty in, you will need to stretch the skin to fit the new size. Flubber will constantly want to stick to skin layer, so you'll need to keep scraping while stretching.
 
Start on a small section at a time. Do not use too much glue. A little goes a long way as long as the glue is evenly spreaded. Let it sit overnight. I have not submerged my Ai Chan so I do not know how air tight the glue is or how it holds up in water. But so far, the glue is doing a good job of holding the skin layer in place during use.

enlarge-busty-aichan-03.jpg

enlarge-busty-aichan-04.jpg

enlarge-busty-aichan-05.jpg

enlarge-busty-aichan-06.jpg


Find Similar Products by Category


Masturbator 101 Blog